Printed in China
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
To assure the finest performance, please read this manual carefully. Keep it in a safe
place for future reference.
Install this unit in a well ventilated, cool, dry, clean place - away from direct
sunlight, heat sources, vibration, dust, moisture, and/or cold. (Do not use/keep this
unit in a car etc.)
Locate this unit away from other electrical appliances, motors, or transformers to
avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold to hot, and do not
locate this unit in an environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
Avoid installing this unit where foreign objects may fall onto this unit and/or this
unit may be exposed to liquid dripping or splashing. On the top of this unit, do
Other components, as they may cause damage and/or discoloration on the
surface of this unit.
Burning objects (i.e. candles), as they may cause fire, damage to this unit,
and/or personal injury.
Containers with liquid in them, as they may fall and liquid may cause electrical
shock to the user and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to
obstruct heat radiation. If the temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not operate this unit upside-down. They may overheat, possibly causing
Do not use force on switches, knobs, and/or cords.
When disconnecting the power cable from the wall outlet, grasp the AC plug; do
not pull the cord.
Do not clean this unit with chemical solvents; this might damage the finish. Use a
clean, dry cloth.
10 Only the voltage specified on this unit must be used. Using this unit with a higher
voltage than specified is dangerous and may cause fire, damage to this unit, and/or
personal injury. Yamaha will not be held responsible for any damage resulting
from use of this unit with a voltage other than that specified.
11 Do not attempt to modify or fix this unit. Contact qualified Yamaha service
personnel when any service is needed. The cabinet should never be opened for any
12 When not planning to use this unit for long periods of time (i.e. when going on
vacation), disconnect the power cable from the AC wall outlet.
13 Be sure to read the “TROUBLESHOOTING” section regarding common operating
errors before concluding that the unit is faulty.
14 Before moving this unit, disconnect the power cable from the wall outlet.
15 Be sure to use the AC adaptor supplied with this unit. Using an AC adaptor other
than the one provided may cause fire or damage to this unit.
16 Install this unit near the wall outlet and where the power cable can be reached
17 For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet.
This will prevent damage to the product due to lightning and power-line surges.
18 The batteries shall not be exposed to excessive heat such as sunshine, fire or the
Keep the batteries in a location out of reach of children. Batteries can be
dangerous if a child were to put in his or her mouth.
If the batteries grow old, the effective operation range of the remote control
decreases considerably. If this happens, replace the batteries as soon as
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and manganese
batteries) together. Read the packaging carefully as these different types of
batteries may have the same shape and color.
Exhausted batteries may leak. If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or letting it come into contact
with clothing, etc. Clean the battery compartment thoroughly before installing
If you plan not to use the unit for a long period of time, remove the batteries
from the unit. Otherwise, the batteries will wear out, possibly resulting in a
leakage of battery liquid that may damage the unit.
Do not throw away batteries with general house waste. Dispose of them
correctly in accordance with your local regulations.
There is a chance that placing this unit too close to a CR
T -based (Braun tube) TV set might
impair picture color
. Should this happen, move this unit a way from the TV set.
THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
Even if an iPhone or iPod is not connected to this unit, this unit is not disconnected from the
AC power source as long as it is connected to the wall outlet. In this state, this unit is designed
to consume a very small quantity of power.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should
be cut off and an appropriate 3 pin plug ﬁtted. F
or details, refer to the instructions described below .
The plug sev
ered from the mains lead must be destroyed, as a plug with bared ﬂexible cord is
hazardous if engaged in a liv
e socket outlet.
or Users on Collection and Disposal of Old Equipment and
These symbols speciﬁed in the Directiv
es 2002/96/EC and 2006/66/EC indicate
that used electrical and electronic products and batteries should not be
general household waste.
For proper treatment to av
oid harmful effect on human health and environment,
please contact your
local municipality , your waste disposal service or the point of sale
where you purchased the items.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it
complies with the requirement set by the Directiv
e for the chemical inv olved.
SPECIAL INSTRUCTIONS FOR U
THE WIRES IN MAINS LEAD
ARE COLOURED IN ACCORD ANCE WITH THE
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with
the letter N or coloured BLA
CK. The wire which is coloured BR OWN must be connected to
the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
Important Notice: Guarantee Inf
ormation for customers in EEA* and Switzerland
For detailed guarantee information about this
Y amaha product, and Pan-EEA* and Switzerland warranty service, please either visi t the website address below (Printable file is available at our
website) or contact the
Y amaha representative office for your country . * EEA: European Economic Area
Setting the c
Setting the alarm
Stopping the alarm
Press and hold down the
for three seconds or longer to activate the power-saving
During the power-saving mode, the front panel display turns of
f. Then the
operations from the remote control, alarm function, and iPhone/iPod charge
function are disabled.
on the control panel to cancel the power-saving mode.
Press and hold down the
on the control panel for two seconds or
The time display will blink.
urn the VOLUME/CLOCK to set to the
DIMMER/CLOCK to set the time.
The time display will light up.
The display will switch between 12-hour display (12H)
and 24-hour display (24H) each time the
is pushed, when setting the clock’ s time.
Press and hold down the ALARM on the
control panel for two seconds or longer
ALARM LED and time display will blink.
urn the V OLUME/CLOCK to set the
the SNOOZE/SLEEP .
The alarm volume display will blink.
urn the V OLUME/CLOCK to adjust the
the ALARM to complete the setting.
ALARM LED and time display will light up.
SNOOZE/SLEEP on the control
panel or remote control.
The alarm will turn off and start again in
ﬁ ve minutes.
• If the iPhone/iPod is connected, the beeping sound will
stop when the
SNOOZE/SLEEP is pushed once and the
s playback will stop when pushed twice.
ﬁ ve minutes of stopping the iPhone/iPod’ s
playback, the playback will start again with an
increasing volume, then the beeping sound will start.
• During the snooze state, the
ALARM LED and POWER
LED will blink.
ALARM on the control panel or remote
• The iPhone/iPod play and beeping sound will stop, and
the alarm will turn off.
ALARM LED will turn off.
If the alarm is not turned off, it turns of
after 60 minutes.
Three minutes before the alarm time, the iPhone/iPod will start playing the current song at
a low volume which will gradually increase.
When the alarm time is reached, a “beeping” sound will start.
Connect the iPhone/iPod before the set alarm time.
If an iPhone/iPod is not connected, the beeping sound will start at the alarm time.
ower on/off DIMMER/CLOCK
• Switches the brightness of the front panel
display (Three levels)
• Sets the clock’
• Switches the alarm’
• Sets the alarm
Push to enable the snooze function and set
the sleep timer
urning the alar m off
Within 6 m
Using the sleep timer
Repeatedly press the
SNOOZE/SLEEP on the
control panel or remote control, and select the
• The display will alternate in the order of "30"
→ "60" →
→ "120" → "current time" with each press of the
The current time will appear and the POWER LED will
blink, when the sleep timer is set.
SNOOZE/SLEEP to disable the sleep timer
during the sleep timer is activated. The POWER LED will
The power is turned off automatically
, after the elapse of a period of time (30/60/90/120
ortable Player Doc k
urning on the P ower
When the power is on, the POWER LED will light up.
Connecting Music Devices
Connect the iPhone/iP
od to the iP od dock.
The battery of the connected iPhone/iPod will be charged.
Be sure to use a dock adaptor included your iPhone/
iPod or applicable commercially available dock
. If you do not use an adaptor or the adaptor is
not compatible, the connection may be loose or poor
causing damage to the connector
. For more information
about the dock adaptor
, refer to Apple's website.
• If the iPhone/iPod is forcibly connected while still
in a protective case, the connector may be damaged.
Make sure to remove any protective iPhone/iPod case
• When the unit is used with the iPhone/iPod shake
ﬂ e function on, the iPhone/iPod might shuf ﬂ e due
to the vibration of speaker depending on the music
played back. If this happens, turn the shake shuf
(Refer to the instruction manual of the iPhone/iPod to turn the function of f.)
• If the iPhone/iPod is connected while playing videos or music on the iPhone/iPod, PDX-13
will turn on automatically and continue the play (except when PDX-13 is in power-saving
Y ou can always connect and disconnect the iPhone/iPod.
• The PDX-13’
s volume level can be adjusted using the iPhone/iPod. The volume level will
also be displayed on the iPhone/ iPod.
Connecting an External Device
Connect to the
AUX on the rear panel.
o connect an external device to PDX-13, use a
commercially available 3.5 mm (1/8 in.) stereo mini
If you start playback on the connected device, sound will come
from the PDX-13's speaker
iPhone/iPod's playback can be controlled using either the included
remote control or the iPhone/iPod itself.
Push to enable the snooz
function and set the sleep
e the insulation
Operate by the
Replacing the Battery
Pull out the battery case as
shown in the diagram below
and change a battery
While pushing the release tab in
, slide out the battery
holder in direction
urning the alar m off temporarily (snooze function)
The current time is
displayed even when
the power is off.
Refer to the table below if the unit does not operate properly
. If the problem you are experiencing is not listed below , or if the instruction below does not
help, turn off the unit, disconnect the power cable, and contact the nearest authorized
Y amaha dealer or service center .
Remedies and P oints to Conﬁ rm
Is the iPhone/iPod connected securely to the iPod dock?
Are PDX-13 and the external device’
s connector cable connected securely? Are the connector •
cable and the external device connected securely?
AC adaptor connected securely? •
to turn on PDX-13.
Is the volume turned down?
Suddenly no sound
Has the sleep timer been set?
Even if the v
olume le vel is raised, the sound le v el
does not increase.
It is possible that the protection circuitry has been activated by excessive volume. Reduce the
Even if the v
olume le vel of the connected iPhone/
od is changed, the sound le vel does not change .
Is the connected iPhone/iPod compatible with PDX-13?
Is the iPhone/iPod connected securely to the iPod dock?
od cannot be controlled using the
PDX-13 cannot be controlled using the remote
Has the power-saving mode been activated? (
urning on the Power")
Are you outside of the remote control operating range?
Has the remote control’
s battery been exhausted, •
or is it inserted incorrectly?
Has the insulation sheet been removed?
od does not pla y at alar m time.
Is the iPhone/iPod connected securely to the iPod dock?
The settings such as the alarm time and clock's
time are changed.
If the electric supply is interrupted due to the power outage, etc. around half a day
, the settings
could be changed. In that case, set them again.
PDX-13 does not operate at all.
In some cases, resetting PDX-13 can solve the problem.
o reset PDX-13, push and hold the
on the control panel for 10 seconds or more.
............................ iPod touch (1st, 2nd, 3rd and 4th generations), iPod classic, iPod with video,
iPod nano (1st, 2nd, 3rd, 4th, 5th and 6th generations)
............................................................................... iPhone 4, iPhone 3GS, iPhone 3G, iPhone
............................................................................... ø 3.5 mm (1/8 in.) stereo mini jack
U.S.A. and Canada models
......................................................................................... AC 120 V , 60 Hz
............................................................................................... AC 100 to 240 V , 50/60 Hz
............................................................................................................. ............................ 8 W
Power consumption when power off and the iPhone/iPod is disconnected
...................................... 1.5 W or less
(Power-saving mode: 0.5
W or less)
MU18-D120150-B2 or MU18-D120150-C5 (DC 12 V
Dimensions (W × H × D)
............................................... 160 mm × 99 mm × 125 mm (6 1/4" × 3 7/8" × 4 7/8")
eight ........................................................................................................................ .......................0.9 kg (2 lbs)
o play an unsupported iPod, such as a 4th generation (or earlier) iPod, iPod shuf ﬂ e, iPod photo, and iPod
mini, connect the iPod to AUX and use it as an external device.
ﬁ cations are subject to change without notice.
* The name plate is located on the bottom of the unit.
"Made for iP
od" and "Made for iPhone"
mean that an electronic accessory has been
designed to connect speciﬁ
cally to iP od or
ely , and has been cer tiﬁ ed
by the de
veloper to meet Apple perf or mance
Apple is not responsible f
or the operation of
this device or its compliance with saf
Please note that the
use of this accessory with iPod or iPhone
ect wireless performance.
od, iP od classic, iP od nano ,
od touch and iT unes are trademarks of
Apple Inc., registered in the U
.S. and other
ﬁ rm that the following accessories are
included before using the unit.
• Remote control •
anel Displa y
Displays the current time,
alarm time, and the
Lights up when the PDX-13’
s power is turned on.
Blinks when the sleep timer is set.
When displaying the time with the 12-hour display
, stays off during
the a.m. hours and lights up during the p.m. hours.
Lights up when the alarm is set.
When an iPhone/iPod and another external device
are connected to PDX-13, audio can be enjoyed in
many ways—for example, by playing music while
listening to the news.
ou can control the PDX-13's volume level by
operating the volume control function on the
Y our iPhone/iP od Battery
Use the alarm function to wake up to music from
your iPhone or iPod.
Connect the included
AC adaptor .
AC adaptor to PDX-13, before
connecting the power cable to the wall outlet.
Adjusts the volume/time.