Tenda Nova MW5s

Tenda Nova MW5s manual

(2)
  • Solid green Good connection
    Solid yellow Fair connection
    Solid red Disconnected
    RST button
    RST button
    DC power jack to connect to
    12 V 1 A power adapter
    DC power jack to connect to
    9 V 1 A power adapter
    WAN/LAN port
    WAN/LAN port
    LAN port
    LAN port
    RST
    PWRLAN
    WAN/LAN
    LED indicator
    RST
    PWRLAN
    WAN/LAN
    Theprimarynode-Mesh5
    Thesecondarynode-Mesh3f
    Ethernet jack
    Or
    DSL
    WAN
    Modem
    Connecting the Primary Node
    1. Power off your modem, and remove its battery (if any).
    2. Use the included Ethernet cable to connect a LAN port of
    your modem or the Ethernet jack to the WAN/LAN port of
    the primary node (A label is on its top panel).
    3. Re-plug your modem and power it on.
    4. Use the 12 V 1 A power adapter to connect the primary node
    to a power source, and its LED indicator lights solid green.
    Wait for about 40 seconds. The system completes startup
    when the LED indicator blinks green.
    Connecting the Mobile Device
    to the Primary Node
    Go to the WiFi network list on your mobile device, select the
    SSID of the primary node, and enter its password. The SSID
    and password are specified on the bottom label of the
    primary node.
    1. For the best performance, place each node:
    in an elevated, open position with coverage area of your
    existing nova WiFi network. This is approximately 20 – 30
    feet or 6 – 9 meters between each node.
    Keep your nodes away from electrical equipment with
    strong interference, such as microwave ovens, induction
    cookers and refrigerators.
    2. Use the 9 V 1 A power adapters to connect the secondary nodes
    to separate power sources, their LED indicators light solid green.
    Wait for about 40 seconds. The secondary node is connecting
    to another node when its LED indicator blinks green.
    Installing the Tenda WiFi App
    Download the Tenda WiFi App onto your mobile device by
    searching for Tenda WiFi in the App Store/Google Play, or by
    scanning the QR code. Then, install the App.
    The MW5s consists of one Mesh5 and one or two Mesh3f. The
    Mesh5 is the primary node and is used to connect to a modem or
    an Ethernet jack, and the Mesh3f is the secondary node used to
    extend the WiFi network of the primary node.
    Use the 12V 1A power adapter to connect to the primary node while
    the 9V 1A power adapters to the secondary nodes for better
    stability.
    TendaWiFi
    Available for iOS and Android
    Or
    3. When all the nodes are connected, the LED indicators on the
    secondary nodes show as follows:
    4. If a node's LED indicator does not light solid green, relocate it
    according to step 1 in to get a better connection.V 
    To access the internet:
    - Wired devices: Connect wired devices to the LAN ports of
    your nodes.
    - Wireless devices: Connect wireless devices to your WiFi
    network using the SSID and password you set.
    If you want to manage the network anytime, anywhere then
    access the App, tap and login to your account.
    NOVA_XXXX
    XXXXXX
    Wi-Fi
    12:23PM
    CHOOSE A NETWORK...
    91%
    Settings
    Wi-Fi
    V
    Connecting the Secondary
    Nodes to the Internet
    Q5: My 2.4 GHz WiFi-enabled devices, such as a home security
    camera, cannot connect to my nova WiFi network. What
    should I do?
    Getting to Know Your Device
    Quick Installation Guide
    AC1200 Whole Home Mesh WiFi System
    MW5s (3-pack)
    Internet
    Connecting the Primary Node
    to the Internet
    Run the Tenda WiFi App and follow the on-screen instructions
    to connect the primary node to the internet.
    After it is connected to the internet, its LED indicator should
    turn a solid green.
    FAQ
    A1: Run the Tenda WiFi App, tap Settings in the lower-right corner,
    tap Wireless Settings, change your SSID and password, and tap
    Save. After changing your SSID and password, you need to
    reconnect your mobile devices using the new SSID and password.
    A2: Tap the node on the Tenda WiFi App, tap“...”in the upper-right
    corner, and choose Delete.
    Note: This removing operation restores the node to factory
    settings.
    A4: With your nodes powered on, hold the Reset (RST) button of your
    primary node down using a reset-pin or a paper clip for about 6
    seconds. Release it when the LED indicator blinks fast. Your
    network is reset successfully when the LED indicator lights solid
    on and then blinks again. And all nodes are then restored to
    factory settings.
    A3: Yes. Run the Tenda WiFi App, tap Settings in the lower-right
    corner, tap Add nova, and follow the on-screen instructions to
    add.
    Q1: How can I change my SSID and password?
    Q2: How can I remove a node from my WiFi network?
    Q4: How to restore my network to factory settings?
    Q3: Can I add another new set of node to expand my network
    coverage?
    A5: ( 1 ) Connect your smart phone used for setup to your nova WiFi
    network.
    (2) Run the Tenda WiFi App, tap Settings, Smart Assistant, and
    Enable. Your smart phone connects to the 2.4 GHz WiFi network.
    (3) Use the smart phone to set up your 2.4 GHz WiFi-enabled device
    guided by the App of the device you would like to connect.
    LED indicator description
    After a node is powered on, the LED indicator lights solid green for
    about 40 seconds to complete startup. Then, the LED indicator lights
    one of the following colors:
    Node Type
    Status
    Description
    The primary node
    Mesh5
    Blinking green
    Connecting to the internet
    Solid green
    Connected to the internet
    Solid red
    Disconnected
    The secondary
    node
    Mesh3f
    Blinking green
    Connecting to the primary node
    Solid green
    Good connection.
    Solid yellow
    Fair connection.
    Solid red
    Disconnected.
    Copyright
    © 2018 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
    Tenda is a registered trademark legally held by Shenzhen Tenda Technology
    Co., Ltd. Other brand and product names mentioned herein are trademarks
    or registered trademarks of their respective holders. Specifications are
    subject to change without notice.
    Technical Support
    Shenzhen Tenda Technology Co., Ltd.
    6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District,
    Shenzhen, China. 518052
    Operating Environment
    Temperature: 0°C-40°C Humidity: (10 - 90)% RH, non-condensing
    Adapter Model: BN036-A12012E/BN036-A12012B/BN036-A12012U
    Manufacturer: SHENZHEN HEWEISHUN NETWORK
    TECHNOLOGY CO., LTD.
    Input: 100-240 V AC, 50/60 Hz, 0.4 A
    Output: 12 V DC, 1 A
    : DC Voltage
    CE Mark Warning
    This is a Class B product. In a domestic environment, this product may
    cause radio interference, in which case the user may be required to take
    adequate measures.
    Operations in the 5.15-5.25GHz band are restricted to indoor use only.
    This equipment should be installed and operated with a minimum
    distance 20cm between the device and your body.
    Declaration of Conformity
    Hereby, Shenzhen Tenda Technology Co., Ltd. declares that the radio
    equipment type Mesh5 is in compliance with Directive 2014/53/EU.
    The full text of the EU declaration of conformity is available at the
    following internet address:
    http://www.tendacn.com/en/service/download-cata-101.html
    NOTE: ( ) The manufacturer is not responsible for any radio or TV
    interference caused by unauthorized modifications to this equipment.
    (2) To avoid unnecessary radiation interference, it is recommended to
    use a shielded RJ45 cable.
    WARNING: The mains plug is used as disconnect device; the disconnect
    device shall remain readily operable.
    1
    FCC Statement
    This equipment has been tested and found to comply with the limits for
    a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
    are designed to provide reasonable protection against harmful
    interference in a residential installation. This equipment generates, uses
    and can radiate radio frequency energy and, if not installed and used in
    accordance with the instructions, may cause harmful interference to
    radio communications. However, there is no guarantee that interference
    will not occur in a particular installation. If this equipment does cause
    harmful interference to radio or television reception, which can be
    determined by turning the equipment off and on, the user is encouraged
    to try to correct the interference by one or more of the following measures:
    Caution:
    Any changes or modifications not expressly approved by the party
    responsible for compliance could void the user's authority to operate
    this equipment.
    This transmitter must not be co-located or operating in conjunction with
    any other antenna or transmitter.
    Operating frequency: 2412-2462MHz, 5150-5250MHz, 5725-5850MHz
    The device is for indoor usage only.
    This device complies with Part 15 of the FCC Rules. Operation is subject
    to the following two conditions: (1) this device may not cause harmful
    interference, and (2) this device must accept any interference received,
    including interference that may cause undesired operation.
    — Reorient or relocate the receiving antenna.
    — Increase the separation between the equipment and receiver.
    — Connect the equipment into an outlet on a circuit different from that
    to which the receiver is connected.
    — Consult the dealer or an experienced radio/TV technician for help.
    Radiation Exposure Statement
    This device complies with FCC radiation exposure limits set forth for an
    uncontrolled environment and it also complies with Part 15 of the FCC
    RF Rules.
    This equipment should be installed and operated with a minimum
    distance 20cm between the device and your body.
    Caution:
    Adapter Model: BN052-A09009U/BN052-A09009E/BN052-A09009B
    Manufacturer: SHENZHEN HEWEISHUN NETWORK
    TECHNOLOGY CO., LTD.
    Input: 100-240 V AC, 50/60 Hz, 0.3 A
    Output: 9 V DC, 1 A
    : DC Voltage
    Caution:
    This product bears the selective sorting symbol for Waste electrical and
    electronic equipment (WEEE). This means that this product must be
    RECYCLING
    Declaration of Conformity
    Hereby, Shenzhen Tenda Technology Co., Ltd. declares that the radio
    equipment type Mesh3f is in compliance with Directive 2014/53/EU.
    The full text of the EU declaration of conformity is available at the
    following internet address:
    http://www.tendacn.com/en/service/download-cata-101.html
    For EU/EFTA, this product can be used in the following countries:
    caused by unauthorized modifications to this equipment. (2) To avoid
    unnecessary radiation interference, it is recommended to use a shielded
    RJ45 cable.
    NOTE:
    (1) The manufacturer is not responsible for any radio or TV interference
    Hong Kong hotline: 00852-81931998
    Website: http://www.tendacn.com
    Email: support.nova@tenda.com.cn
    Canada hotline: 1-888-998-8966
    Toll Free: Mon - Fri 9 am - 6 pm PST
    Operating Frequency:
    2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
    5 GHz: EU/5150-5250MHz (CH36-CH48)
    EIRP Power (Max.):
    2.4 GHz: 19.5 dBm 5 GHz: 22 dBm
    Software Version: V1.0.0.X
    Operating Frequency:
    2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
    5 GHz: EU/5150-5250MHz (CH36-CH48)
    EIRP Power (Max.):
    2.4 GHz: 19.67 dBm 5 GHz: 22.21 dBm Software Version: V1.0.0.X
    USA hotline: 1-800-570-5892
    Toll Free: Daily-9am to 6pm EST
    AC1200 Whole Home Mesh WiFi System
    Model Mesh5
    Power 12V 1A
    FCC ID V7TMESH5
    IC 9034A-MESH5
    MAC
    SN
    This device complies with part 15 of the FCC Rules.
    Operation is subject to the following two conditions:
    (1) This decive may not cause harmful interference.
    (2) this decive must accept any interference received,
    including interference that may cause undesired operation.
    SSID:
    NOVA_XXXX
    Password:
    12 V 1 A power
    adapter
    Done.
    WAN/LAN
    Mesh5 x 1
    9 V 1 A power adapter x 2
    Quick installation guidex1Ethernet cablex 1
    Package contents
    12 V 1 A power adapter x 1
    Mesh3f x 2
    RST
    PWRLAN
    WAN/LAN
    Tips
    CAN ICES-3(B)/NMB-3(B)
    handled pursuant to European directive 2012/19/EU in order to be recycled
    or dismantled to minimize its impact on the environment.
    User has the choice to give his product to a competent recycling
    organization or to the retailer when he buys new electrical or electronic
    equipment.

Brug for hjælp?

Antal spørgsmål: 0

Har du et spørgsmål om Tenda Nova MW5s eller har du brug for hjælp? Stil dit spørgsmål her. Giv en klar og omfattende beskrivelse af problemet og dit spørgsmål. Jo flere oplysninger du giver om dit problem og dit spørgsmål, jo lettere er det for andre Tenda Nova MW5s ejere at svare korrekt på dit spørgsmål.

Se manualen til Tenda Nova MW5s her gratis. Denne vejledning hører under kategorien Access points og er blevet bedømt af 2 personer med et gennemsnit på en 7.6. Denne manual er tilgængelig på følgende sprog: Engelsk. Har du et spørgsmål om Tenda Nova MW5s eller har du brug for hjælp?

Tenda Nova MW5s specifikationer

Mærke Tenda
Model Nova MW5s
Produkt Access Point
EAN 6932849428063
Sprog Engelsk
Filtype PDF
Design
Produkttype Bærbar router
Farve på produkt Hvid
Kontrollampe
Farve på produkt Hvid
Knap til nulstilling
Godkendelse FCC, CE, RoHS, EAC, IC
Placering Bord
LED-indikatorer Signal strength, System
WAN-forbindelse
Ethernet WAN
DSL WAN
SIM-kort slot
3G/4G kompatibilitet USB-modem
Trådløse LAN funktioner
Wi-Fi-bånd Dual-band (2, 4 GHz / 5 GHz)
Bedste Wi-Fi standard Wi-Fi 5 (802.11ac)
WLAN dataoverførselshastighed (maks) 867
WLAN dataoverførselshastighed (første bånd) 300
WLAN dataoverførselshastighed (anden bånd) 867
Wi-Fi-standarder 802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Antenne
Antenne type Intern
Niveau for antennestyrke (maks.) 3
Antenner, antal 2
Antenne type Intern
Niveau for antennestyrke (maks.) 3
Antenner, antal 2
Antenneretningstype Omniretningsbestemt
Antennefunktioner Integreret antenne
Netværk
Ethernet LAN
Ethernet LAN-grænsefladetype Gigabit Ethernet
Ethernet LAN-datahastigheder 10, 100, 1000
Kabelteknologi 10/100/1000Base-T(X)
Netværksstandarder IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11k, IEEE 802.11n, IEEE 802.11r, IEEE 802.11v, IEEE 802.3, IEEE 802.3u
Portvideresendelse
SSID-baseret VLAN-opgave
Statisk rute
VPN-support IPsec pass through, PPTP pass through, L2TP pass through
Funktioner
Firmware kan opgraderes
Godkendelse FCC, CE, RoHS, EAC, IC
Ethernet LAN-datahastigheder 10, 100, 1000
Netværksstandarder IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11k, IEEE 802.11n, IEEE 802.11r, IEEE 802.11v, IEEE 802.3, IEEE 802.3u
2.4 GHz
5 GHz
Maksimal dataoverførselshastighed (5 GHz) 867
Maksimal dataoverførselshastighed (2,4 GHz) 300
Maksimal dataoverførselshastighed 1200
MIMO
MIMO type Multi User MIMO
Mobilt netværk
3G
4G
Strømstyring
Strømkilde type DC
AC indgangsspænding 100 - 240
AC frekvens 50/60
Udgangsspænding 12
Udgangsstrøm 1
Strøm over Ethernet (PoE)
Udgangsspænding 12
Udgangsstrøm 1
Strøm over Ethernet (PoE)
Indgangsspænding 100 - 240
Indgangsfrekvens 50/60
Indgangsstrøm 0.6
Driftsbetingelser
Driftstemperatur (T-T) 0 - 40
Opbevaringstemperatur (T-T) -40 - 70
Relativ luftfugtighed ved drift (H-H) 10 - 90
Relativ luftfugtighed ved opbevaring (H-H) 5 - 90
Driftstemperatur (T-T) 0 - 40
Opbevaringstemperatur (T-T) -40 - 70
Relativ luftfugtighed ved drift (H-H) 10 - 90
Relativ luftfugtighed ved opbevaring (H-H) 5 - 90
Porte & Grænseflader
Ethernet LAN-porte (RJ-45) 2
USB-port
Hukommelseskortstik
DC-in-stik
Ethernet LAN-porte (RJ-45) 2
DC-in-stik
Antal USB 2.0-porte 0
WAN-forbindelse Ethernet (RJ-45)
Vægt & størrelser
Bredde 91
Dybde 91
Højde 93
Bredde 91
Dybde 91
Højde 93
Administrationsfunktioner
Knap til nulstilling
Firmware kan opgraderes
Sikkerhed
Sikkerhedsalgoritmer WPA2-PSK
Firewall
Firewall sikkerhed UDP flood attack defence, TCP flood attack defence, ICMP flood attack defence
Gæsteadgang
Sikkerhedsalgoritmer WPA2-PSK
VPN-support IPsec pass through, PPTP pass through, L2TP pass through
Service Set Identifier (SSID) funktioner SSID-udsendelse
Emballeringsdata
Antal medfølgende produkter 3
Pakketype Kasse
AC-adapter inkluderet
Kabler inkluderet LAN (RJ-45)
Hurtig installationsvejledning
Antal medfølgende produkter 3
Pakketype Kasse
AC-adapter inkluderet
Kabler inkluderet LAN (RJ-45)
Protokoller
DHCP-klient
DHCP-server
Universal Plug and Play (UPnP)
DHCP-klient
DHCP-server
Universal Plug and Play (UPnP)
Andre funktioner
Firewall sikkerhed UDP flood attack defence, TCP flood attack defence, ICMP flood attack defence
Præstation
Kompatible operativsystemer Android 4.0+, iOS 8+

Relaterede produkter Tenda Nova MW5s

    Relaterede produktmanualer

    Access Point Tenda

    Tilføj manual

    Har du en manual, som du gerne vil tilføje?