Congratulations on your purchase and welcome to Philips! To fully
benet from the support that Philips offers, register your product
Read this user manual carefully before you use the appliance and save it for
- Never immerse the motor unit in water or any other liquid, nor rinse it
under the tap. Only use a moist cloth to clean the motor unit.
- Check if the voltage indicated on the appliance corresponds to the local
mains voltage (110-120/127V or 220-230/240V) before you connect
- Do not use the appliance if the plug, the mains cord or other parts are
- If the mains cord is damaged, you must have it replaced by Philips, a
service centre authorised by Philips or similarly qualied persons in
order to avoid a hazard.
- Do not touch the blades, especially when the appliance is plugged in.
The blades are very sharp.
- Never reach into the blender jar with your ngers or an object while
the appliance is running.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
- Children should be supervised to ensure that they do not play with
- Never let the appliance run unattended.
- If the blades get stuck, unplug the appliance before you remove the
ingredients that block the blades.
- Never use the blender jar to switch the appliance on and off.
- Always unplug the appliance from the mains before you assemble,
disassemble or make adjustments to any of the parts.
- Never use any accessories or parts from other manufacturers or that
Philips does not specically recommend. If you use such accessories or
parts, your guarantee becomes invalid.
- Do not exceed the maximum level indicated on the blender jar.
- Always make sure the lid is properly closed and the measuring cup is
inserted properly before you switch on the appliance.
- Never ll the blender jar with ingredients hotter than 80°C/175°C.
Electromagnetric elds (EMF)
This Philips appliance complies with all standards regarding electromagnetic
elds (EMF). If handled properly and according to the instructions in this
user manual, the appliance is safe to use based on scientic evidence
Built-in safety lock
This feature ensures that you can only switch on the appliance if you have
properly assembled the blender jar on the motor unit. If the jar is correctly
assembled, the built-in safety lock will be unlocked.
The blender (Fig. 1)
A Motor unit
B 0 = OFF button
C PULSE/QUICK CLEAN button
D Speed buttons (1 to 3)
E Integrated blade unit
F Level indication
G Blender jar
H Lid of blender jar
I Lid opening lever
J Measuring cup
L Filter (HR2034 only)
1 Thoroughly clean the parts that come into contact with food before
you use the appliance for the rst time (see chapter ‘Cleaning’).
Using the blender
The blender is intended for:
- Blending uids, e.g. dairy products, sauces, fruit juices, soups, mixed
- Mixing soft ingredients, e.g. pancake batter or mayonnaise.
- Pureeing cooked ingredients, e.g. for making baby food.
1 Press the lid opening lever to open the lid. (Fig. 2)
- You only need to remove the lid for cleaning purposes (Fig. 3).
2 Put the ingredients in the blender jar (Fig. 4).
To avoid spillage, do not put more than 1.5 litres of liquid in the blender
jar, especially when you want to process at a high speed. Do not put more
than 1.1 litres in the blender jar when you want to process hot liquids or
ingredients that tend to foam.
Do not process more than one cup of dry ingredients at a time.
3 Place the jar on the motor unit (1) and turn it clockwise by the
handle to fasten it (2). (Fig. 5)
4 Close the lid and insert the measuring cup into the lid (Fig. 6).
To prevent spillage, always insert the measuring cup into the lid before you
5 Put the mains plug in the wall socket.
6 Press one of the speed buttons to switch on the appliance (Fig. 7).
Do not let the blender run for more than 3 minutes at a time. If you have
not nished blending after 3 minutes, switch off the appliance for one
minute before you continue blending.
Do not process dry ingredients for more than 1 minute.
7 If you want to process ingredients very briey, press the PULSE/
QUICK CLEAN button several times (Fig. 8).
Never press the PULSE/QUICK CLEAN button longer than a few
seconds at a time.
8 You can use the opening in the lid to add ingredients while the
appliance is running (Fig. 9).
9 Press the OFF button (0) to switch off the appliance. (Fig. 10)
- Do not prepare recipes that contain large quantities of oil or fat.
- Cut solid ingredients into smaller pieces before you put them in the
blender. Do not process a large quantity of dry ingredients at the same
time. Process these ingredients in a series of small batches instead.
- If you are not satised with the results when you blend solid ingredients,
switch off the blender and press the PULSE/QUICK CLEAN button a
few times to let the blender run briey. You can also stir the ingredients
with the provided spatula, as long as it rests on the lid (even when
the blender is running). If you want to use the spatula without resting
it on the lid, switch off the appliance, open the lid and then stir the
ingredients. You can also remove some of the contents of the jar and
process smaller amounts.
- To crush ice cubes, put max. 5 cubes at a time in the jar and press the
PULSE/QUICK CLEAN button a few times. Keep the lid on the jar
Filter (HR2034 only)
You can use the lter to obtain extra nely blended sauces, fresh fruit juices
or cocktails. All pips and skins are caught in the lter.
Never ll the lter beyond its metal part.
Do not use the lter to process hot ingredients.
1 Remove the jar from the motor unit.
2 Open the lid (Fig. 2).
3 Put the lter in the blender jar (Fig. 11).
The grooves of the lter and the ribs inside the blender jar help you put the
lter in the right position.
4 Close the lid to x the lter in its proper position (Fig. 12).
5 Assemble the jar onto the motor unit.
6 Put the ingredients in the lter through the opening in the lid (Fig. 13).
Cut fruits into smaller pieces and soak dried pulses, such as soy beans,
before you process them in the lter.
7 Add water or another liquid.
8 Put the measuring cup in the lid, press speed button 3 (highest speed)
and let the appliance run for max. 40 seconds.
9 Press the OFF button (0) to switch off the appliance (Fig. 10).
10 Pour out the drink through the spout of the blender jar (Fig. 14).
Make sure the lid is closed and the measuring cup is in the lid. This prevents
pulp and skins from ending up in your drink.
11 For optimal results, put the jar with the remaining ingredients back
onto the appliance with the lid closed. Then let the appliance run for a
few more seconds.
12 Pour out the rest of the drink.
- Particularly when you process large quantities, we advise you not to put
all the ingredients in the lter at the same time. Start to process a small
quantity, let the appliance run for a moment, switch it off and then add
another small quantity.
- To get the best result when you make fruit juices and cocktails, add
approx. 300ml water to 150g fruit. You can also use other liquids, e.g. to
You can use the spatula to prepare smoothies and other recipes which are
difcult to blend.
1 Put the ingredients in the blender jar.
2 Close the lid and insert the spatula into the jar through the hole in
the lid (Fig. 15).
Do not use any other spatula than the one provided with this appliance.
Do not use the spatula if the lid is open.
3 Press one of the speed buttons to switch on the appliance (Fig. 7).
4 Use the spatula when needed. Move it up and down or anticlockwise
for thorough blending (Fig. 16).
Note: You can safely move the spatula while the blender is running as long as
the spatula rests on the lid.
Always unplug the appliance before you clean it.
Never immerse the motor unit in water, nor rinse it under the tap. Do
not clean the motor unit in the dishwasher.
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the appliance.
Tip: Cleaning the appliance and its parts is easiest immediately after use.
1 Make sure the appliance is unplugged.
2 Disassemble all removable parts from the motor unit.
3 Clean the motor unit with a moist cloth.
4 Clean the removable parts in hot water, if necessary with some
washing-up liquid, or in the dishwasher.
All removable parts are dishwaher proof, except for the motor unit.
Note: If you have to clean the mesh of the lter, use a very soft brush.
Quick-cleaning the blender jar
1 Fill the blender halfway with warm water and add a few drops of
2 Press the PULSE/QUICK CLEAN button a few times (Fig. 8).
3 Detach the blender jar, empty it and rinse it under the tap.
1 To store the mains cord, wind it round the reel in the bottom of the
appliance (Fig. 17).
HR2030: You can order the lter from your Philips dealer.
- Do not throw away the appliance with the normal household waste
at the end of its life, but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the environment. (Fig. 18)
Guarantee & service
If you need service or information or if you have a problem, please visit
the Philips website at www.philips.com or contact the Philips Consumer
Care Centre in your country (you nd its phone number in the worldwide
guarantee leaet). If there is no Consumer Care Centre in your country, go
to your local Philips dealer.
- 90g dried soy beans
- 600ml water
1 Soak the soy beans for 4 hours before you process them.
2 Pour the soaked soy beans and the water in the lter. Blend for 24
seconds at the highest speed.
Do not process more than 1 batch without interruption. Let the
appliance cool down to room temperature before continue processing.
3 Bring the soy milk to the boil in a pan, then add sugar and leave to
Frequently asked questions
This chapter lists the questions most frequently asked about the appliance.
If you cannot nd the answer to your question, contact the Customer Care
Centre in your country.
Can I clean
parts in the
Yes, except the motor unit. Only clean the motor unit
with a moist cloth.
When you press the PULSE/QUICK CLEAN button,
the appliance runs at its highest speed until you
release the button. Use the PULSE/QUICK CLEAN
button when you want to have more control over
the processing jobs. You can also use this button
to quick-clean the blender jar (see chapter ‘Cleaning’).
Can I pour boiling
hot liquids into
the blender jar?
No, let hot liquids cool down to 80°C/175°F to
prevent damage to the jar.
It is normal for a new appliance to give off an
unpleasant smell or emit some smoke the rst few
times it is used. This phenomenon stops after you
have used the appliance a few times. If the appliance
has been switched on too long, it may also give off
an unpleasant smell or emit some smoke. In this case,
switch off the appliance and let it cool down for 60
blade unit is
should I do?
Press the OFF button (0) and use a spatula to
dislodge the ingredients that block the blade unit. We
also advise you to process a smaller quantity.
Why does the
fruit juice or soy
milk contain a lot
of pulp or skins?
To prevent pulp and skins from ending up in your
drink, make sure that the lter is properly placed
in the jar. Also make sure the lid is closed and the
measuring cup is inserted in the lid.
Register your product and get support at
Register your product and get support at
2 3 4 5
7 8 9
10 11 12 13
14 15 16 17
3101_106_0519_1_DFU-Leaflet_A6_v2.indd 1 20-10-11 13:49