JL Audio MMR-20-BE

JL Audio MMR-20-BE manual

(1)
  • MMR-20-BE
    MediaMaster•
    Wired
    Remote
    Controller
    Product
    Description
    The MMR-20-BE
    is
    a water-resistant
    (IP67
    rated), wired remote controller designed
    to
    add auxiliary control functionality
    to
    MediaMaster'" source units. Depending
    on your system layout, you may add up
    to
    three
    MMR-20-BE
    remote controllers
    to
    a
    single source unit.
    Each
    MMR-20-BE
    can be
    connected up
    to
    75
    ft.
    (22.8
    m)
    away from its
    source unit. A
    Y-splitter and remote extension
    cables
    are
    sold separately and available in
    different lengths
    to
    suit different
    mounting
    locations.
    What's
    Included
    (1)
    MMR
    -
    20-BE
    wired remote controller
    (1)
    Lipped gasket (preinstalled)
    (1)
    Flat gasket (optional)
    (2)
    Stainless steel threaded studs
    (4)
    Stainless steel nuts
    (7
    mm)
    (4)
    Stainless steel washers
    (1)
    Aluminum (-bracket
    (1)
    User
    Manual
    Safety
    Considerations
    ·While
    this
    product
    is
    designed to be water-
    resistant,
    it
    should never be submerged
    under water or subjected
    to
    high-pressure
    water
    spray.
    Do
    not
    mount
    in
    areas
    of
    extreme heat.
    Ensure
    this
    product
    is
    securely installed
    so
    that
    it
    does
    not
    come loose in the event
    of
    a collision/sudden
    jo
    lt
    or
    as
    a result
    or repeated vibrations during normal
    operation.
    ·Check
    before drilling
    to
    make
    sure
    that you
    will
    not
    be drilling into a fuel tank, gas/brake
    line, wiring harness, or other vital system.
    Secure
    all
    wiring
    as
    needed, using cable
    ties
    or
    wire clamps
    to
    protect
    them
    from
    moving parts and sharp edges.
    Mounting &
    Installation
    A 2-inch
    (SO
    mm) hole
    is
    required for
    mounting, along
    with
    adequate
    rear
    access
    to
    secure/tighten the hardware. The included
    hardware accommodates installations in flat
    panels up
    to
    1.5-inches
    (38
    mm) thick.
    The (-bracket
    is
    designed
    with
    break lines
    to
    allow adjustment for different
    mounting
    panel thicknesses.
    To
    remove a leg section,
    use
    pliers and bend back and forth at
    a break line
    to
    separate.
    Be
    mindful
    of
    resultant sharp edges and file
    if
    necessary.
    UIMPORTANTI
    Make
    sure
    to
    carefully
    plan
    the
    routing
    of
    the
    remote's
    connection
    cables
    prior
    to
    cutting
    or
    drilling
    any
    panels
    .
    1. Select
    an
    appropriate
    mounting
    location
    and cut a 2-inch
    (50
    mm) hole
    us
    ing
    an
    appropriate
    tool/hole
    saw.
    2.
    The preinstalled lipped gasket
    can
    be
    used
    for most installations or where
    an
    existing
    mounting hole may be slightly larger than
    2-inches.
    If you desire a reduced profile
    appearance, you may replace the lipped
    gasket with the optional flat
    gasket.
    3.
    Apply thread sealer (not included)
    onto
    the threaded studs and insert
    them
    into
    the inserts at
    the
    rear
    of
    the
    MMR
    -
    20
    -
    BE
    and hand tighten. '
    4.
    Install a nut and washer near the middle
    section
    of
    each stud
    (see
    diagram) and
    place the
    MMR-20-BE
    into the
    mounting
    hole.
    5.
    From behind the
    mounting
    panel, slide
    the
    ( -bracket
    onto
    the threaded studs and
    press
    it
    forward, towards the MMR-
    20
    -
    BE
    6. Apply thread sealer and adjust the position
    of
    the previously installed nuts and
    washers to support the (-bracket while
    still allowing the legs
    to
    of
    the (-bracket
    to
    press
    against the
    rear
    of
    the
    mounting
    panel.
    7.
    Apply thread
    sea
    ler and install a remaining
    nut
    and washer
    onto
    each stud. Tighten
    the
    C-bracket to
    th
    e
    mounting
    panel.
JL Audio MMR-20-BE

Brug for hjælp?

Antal spørgsmål: 0

Har du et spørgsmål om JL Audio MMR-20-BE eller har du brug for hjælp? Stil dit spørgsmål her. Giv en klar og omfattende beskrivelse af problemet og dit spørgsmål. Jo flere oplysninger du giver om dit problem og dit spørgsmål, jo lettere er det for andre JL Audio MMR-20-BE ejere at svare korrekt på dit spørgsmål.

Se manualen til JL Audio MMR-20-BE her gratis. Denne vejledning hører under kategorien Fjernbetjeninger og er blevet bedømt af 1 personer med et gennemsnit på en 7.5. Denne manual er tilgængelig på følgende sprog: Engelsk. Har du et spørgsmål om JL Audio MMR-20-BE eller har du brug for hjælp? Stil dit spørgsmål her

JL Audio MMR-20-BE specifikationer

Mærke JL Audio
Model MMR-20-BE
Produkt Fjernbetjening
Sprog Engelsk
Filtype PDF

Relaterede produktmanualer

Fjernbetjening JL Audio

Ofte stillede spørgsmål

Nedenfor finder du de hyppigst stillede spørgsmål om JL Audio MMR-20-BE.

Er dit spørgsmål ikke angivet? Stil dit spørgsmål her

Vi anvender cookies for at sikre at vi giver dig den bedst mulige oplevelse af vores website. Hvis du fortsætter med at bruge dette site vil vi antage at du er indforstået med det.

Læs mere